Fixture Installation in Des Plaines, IL — Skill and Care You Can Count On
We’re often called out to fix installations that didn’t go as planned. Installing a faucet or fixture isn’t always complicated, but small oversights can cause leaks and damage down the line. Maybe the supply line was only finger-tightened, or an old shutoff valve breaks when turned. A wax ring installed unevenly can leak silently under a toilet for months. A P-trap set too high can cause constant backups. Catching these issues early with a thorough inspection prevents costly repairs later.
When you hire us at 224-257-7145, we carefully remove your old fixture, check the condition of supply lines, shutoff valves, drains, and mounting hardware, and address any problems before installing the new fixture. We make sure everything’s sealed and tested before leaving. If any components need replacement—like a corroded valve—we let you know upfront instead of springing surprises on you after the water’s been shut off. That’s how we do business.
We also offer full-service bathroom fixture installations and kitchen plumbing upgrades. Plus, we can handle your garbage disposal installation or drain maintenance during the same visit for convenience.
Types of Fixtures We Install in Des Plaines
Kitchen & Bathroom Faucets
Replacing faucets is a routine job we handle every day. The trick is in what’s under the sink. We remove your old faucet, clean the sink surface, install the new faucet following manufacturer guidelines, connect new braided stainless steel supply lines (no reused plastic or old copper), and test for leaks under pressure before finishing up.
We regularly deal with issues like stuck shutoff valves that must be swapped out, sink decks with odd hole patterns needing adapters or deck plates, and rusty mounting hardware. If there’s water damage or signs of previous leaks beneath the sink, we’ll perform a quick leak assessment so you’re not sealing in hidden problems. We stock common replacement parts and install all major brands including Moen, Delta, Kohler, and others.
Toilet Installation & Replacement
A proper toilet installation means no rocking, no leaks at the base, quiet operation, and a lasting seal on the flange. We take out your old toilet, inspect and repair or replace the floor flange if it’s cracked or corroded, install a quality wax ring or wax-free seal, set and level the new toilet, and tighten floor bolts to spec—too loose causes movement, too tight risks cracking porcelain. After hooking up the water supply, we check flush performance and inspect for leaks before wrapping up.
We install a full range of toilets: standard, comfort height (ADA compliant), elongated or round bowls, dual-flush models, gravity-fed, and pressure-assisted units. If you’re remodeling your bathroom, we can coordinate rough-in measurements so your new toilet fits perfectly. We also address any non-standard rough-in situations before you shop for your new toilet.
Showerheads & Shower Valves
Swapping out a showerhead is usually straightforward—a quick 30-minute job. We remove the old head, clean the threads on the shower arm, apply fresh thread seal tape, and install the new fixture, testing for leaks and water pressure.
For more complex jobs like replacing shower valves or upgrading to thermostatic or pressure-balance valves, or installing multi-function shower systems with body sprays and handheld wands, we carefully open the wall from an access point or tile, swap the valve body, and fit the new trim. This requires shutting off water to the bathroom, so we’ll discuss details before scheduling. We install major valve brands like Moen, Delta, and Kohler.
Outdoor Faucets & Frost-Free Hose Bibs
Our cold Illinois winters are hard on outdoor faucets. Standard hose bibs left connected to hoses during freezing temps often crack because water trapped between the valve and exterior wall freezes and expands. We specialize in installing frost-free anti-siphon hose bibs that drain water back inside the wall when shut off, protecting your plumbing.
If your outdoor faucet is leaking inside the wall or won’t flow, we’ll replace it with a frost-free model. We can also install dedicated shutoff valves for outdoor taps—so you can turn off water outside each fall without shutting off your entire home supply. If you want to add a new outdoor faucet, we can tap into your interior plumbing and run supply lines. Give us a call at 224-257-7145 before the cold hits.
Other Fixtures & Plumbing Components
Beyond faucets and toilets, we install laundry sinks, utility and bar sinks, bathtub spouts and diverters, bidet seats and standalone bidets, pot fillers (which require hot and cold supply lines routed to the range), touchless and sensor-activated faucets, water filtration faucets, shutoff valves and angle stops, as well as P-traps and drain assemblies. If it connects to your kitchen or bathroom water or drain, we can install it—call us at 224-257-7145.
Why Hire a Licensed Plumber for Fixture Installation?
- Secure connections: Just tightening by hand won’t stop leaks. Proper tools and technique ensure a watertight seal.
- Valve and supply line checks: Old shutoff valves and supply lines often need swapping out during fixture upgrades. We identify and address these upfront.
- Floor flange condition: Damaged or misaligned toilet flanges can cause leaks below your toilet if not repaired before installation.
- Warranty compliance: Many fixtures require professional installation to keep warranties valid.
- Building code adherence: Correct venting, drain sizing, and supply line setups follow local Illinois plumbing codes—our plumbers know the rules.
Complete List of Fixtures We Install
- Kitchen and bathroom faucets of all styles
- Standard, comfort-height, and dual-flush toilets
- Showerheads and shower valve assemblies
- Bathtub spouts and diverters
- Frost-free outdoor hose bibs
- Utility, bar, and prep sinks
- Bidet seats and freestanding bidets
- Pot filler faucets
- Water filtration system faucets
- Angle stops and shutoff valves
- P-traps and drain hardware
Fixture Installation FAQ
Yes, we’re happy to install fixtures you’ve already bought. Just double-check you’ve got all parts, hardware, and the installation instructions. It’s best to have everything ready before we arrive to avoid delays.
While DIY is possible, many issues arise like seized shutoff valves, unusual plumbing layouts, or improper sealing that cause leaks and headaches. A professional install usually takes 1–2 hours and ensures a long-lasting, leak-free job. Toilets especially need a proper flange seal—something that’s tricky to get right without experience.
In many older homes around Des Plaines, shutoff valves haven’t been used in years and can be stuck or corroded. We carry replacement angle stop valves on our truck for these situations. Before doing any replacement, we’ll give you an estimate so you know exactly what to expect. This is a routine issue, especially in homes built decades ago.
Yes, this is a common call every spring in Illinois. Frozen hose bibs usually can’t be repaired and must be replaced. We install durable frost-free anti-siphon hose bibs and add dedicated shutoff valves so you can easily winterize your outdoor plumbing each fall. Call 224-257-7145 and we’ll typically get this handled within the week.